- Welcome to NuTyX official Forum.
NuTyX is a complete GNU/Linux distribution
Recent posts
#21
General / Shutdown issues
Last post by devlin7 - Sat Feb 17 04:58:06 2024Hi,
I have two old hp laptops, a 6550b and an elitebook. I swap disks and try various distros but Nutyx is home for me. The one thing I struggle with is shutdown. The process starts, and seems to do the complete shutdown process but I end up with a black screen but the laptop doesn't turn off. Initially, I thought it was to do with a SMB mount but even with the mount detached it doesn't go down. The kicker is that a reboot works. I don't have an issue with other distros shutting down but I don't want to use them. Issue happens on KDE, openbox, Enlightenment, i3. Any suggestions?
Graeme
I have two old hp laptops, a 6550b and an elitebook. I swap disks and try various distros but Nutyx is home for me. The one thing I struggle with is shutdown. The process starts, and seems to do the complete shutdown process but I end up with a black screen but the laptop doesn't turn off. Initially, I thought it was to do with a SMB mount but even with the mount detached it doesn't go down. The kicker is that a reboot works. I don't have an issue with other distros shutting down but I don't want to use them. Issue happens on KDE, openbox, Enlightenment, i3. Any suggestions?
Graeme
#22
General / Re: Wireguard Package Request ...
Last post by Thierry - Wed Feb 14 06:37:03 2024 #23
General / Re: Wireguard Package Request
Last post by Thierry - Tue Feb 13 09:38:31 2024Will look at it tonight and if not too complicated you have it soon
BR,
Thierry
BR,
Thierry
#24
General / Wireguard Package Request
Last post by ndawka - Mon Feb 12 22:19:37 2024Hello!
I just noticed, that Wireguard (https://www.wireguard.com/) seems to be absent from NuTyX repositories? I tried searching for it in the packages, but couldn't find anything even remotely close...
I would need to use Wireguard ASAP. Is there any way to add it to the NuTyX depot?
Thank you in advance!
Regards
I just noticed, that Wireguard (https://www.wireguard.com/) seems to be absent from NuTyX repositories? I tried searching for it in the packages, but couldn't find anything even remotely close...
I would need to use Wireguard ASAP. Is there any way to add it to the NuTyX depot?
Thank you in advance!
Regards
#25
Release of the latest NuTyX version / NuTyX 24.02.0 available with c...
Last post by Thierry - Sun Feb 11 10:45:18 2024 #26
General / Re: Fix Printing (No Print Ser...
Last post by spiky - Sat Dec 30 08:54:35 2023Hi I will get this fixed, I tested and comfirm adding "cups-pk-helper" fixes the issue
#27
Installation / Keyboard Layout on fresh GNOME...
Last post by ndawka - Wed Dec 27 21:19:48 2023Hello!
I noticed a tiny post-install issue. After NuTyX GNOME installation, I went to the "Keyboard" section in the GNOME Settings and noticed, that in the keyboard layout list there was just "uk". When trying to find that in the "add layout" selection, I found that it was listed as "English (UK)" (which, in this case, are the same). Upon adding that, I had both "uk" and "English (UK)". I have not tested this with other layouts and DEs (such as KDE Plasma). It would be nice, if NuTyX could be installed with the correct layout name. Not critical, but looks out of place, especially when adding a second layout.
Regards
I noticed a tiny post-install issue. After NuTyX GNOME installation, I went to the "Keyboard" section in the GNOME Settings and noticed, that in the keyboard layout list there was just "uk". When trying to find that in the "add layout" selection, I found that it was listed as "English (UK)" (which, in this case, are the same). Upon adding that, I had both "uk" and "English (UK)". I have not tested this with other layouts and DEs (such as KDE Plasma). It would be nice, if NuTyX could be installed with the correct layout name. Not critical, but looks out of place, especially when adding a second layout.
Regards
#28
General / Fix Printing (No Print Service...
Last post by ndawka - Wed Dec 27 21:08:14 2023Hi,
I noticed this on the GNOME version of NuTyX. If I go to the Printers menu in the gnome-control-center (AKA Settings), I cannot add a printer because "No Print Service" is detected. In fact, at the top it says "Error: some settings cannot be unlocked". Launching it from the terminal (GNOME Console) returns the following:
Thank you in advance!
I noticed this on the GNOME version of NuTyX. If I go to the Printers menu in the gnome-control-center (AKA Settings), I cannot add a printer because "No Print Service" is detected. In fact, at the top it says "Error: some settings cannot be unlocked". Launching it from the terminal (GNOME Console) returns the following:
Quotecc-printers-panel[ 2392]: WARNING: Your system does not have the cups-pk-helper's policy "org.opensuse.cupspkhelper.mechanism.all-edit" installed. Please check your installationI also tested it on a fresh NuTyX installation in a virtual machine, the result was the same.
Thank you in advance!
#29
General / Re: New Package with Itself as...
Last post by ndawka - Mon Dec 25 20:44:04 2023Hi Thierry!
Thank you ever so much for adding these packages! I can compile zig manually from source for the moment being, so no rush with that. But it is great, that you have added the other two!
As far as iftop and julia go, I will test them, when I am back at my work space.
Overall it was a pleasure working with you! Have a great holiday and a happy New Year! ::)
Thank you ever so much for adding these packages! I can compile zig manually from source for the moment being, so no rush with that. But it is great, that you have added the other two!
As far as iftop and julia go, I will test them, when I am back at my work space.
Overall it was a pleasure working with you! Have a great holiday and a happy New Year! ::)
#30
General / Re: New Package with Itself as...
Last post by Thierry - Mon Dec 25 19:55:25 2023Hi Ndawka
So far I could build the iftop and julia-bin packages.
You will find them in cli-extra (julia-bin) and gui-extra (iftop) of the rolling version (not in testing).
I did check the recept in AUR from archlinux. Much too much complicate for my little brain.
Enjoy the lasts 2023 days and wish you a good start in 2024
Thierry
So far I could build the iftop and julia-bin packages.
You will find them in cli-extra (julia-bin) and gui-extra (iftop) of the rolling version (not in testing).
I did check the recept in AUR from archlinux. Much too much complicate for my little brain.
Enjoy the lasts 2023 days and wish you a good start in 2024
Thierry