Recent Posts

Pages: 1 ... 8 9 [10]
91
From ISO / [Solved] Installation issues
« Last post by mannequin on Fri Dec 21 15:03:56 2018 »
Hello,

I have tried unsuccessfully to install this a few times. I tried doing as much searching as I could before posting here, but to no avail.

I am having issues with the minimal installer and the graphical installer, both in BIOS and UEFI. This is what I am running into with both from two different installers;

I am trying to install this on a separate SSD that has been formatted and not partitioned. The goal is to have a UEFI dual boot system

What am I missing?

Thanks

Edit: Those two pictures are showing what happens right after booting from the USB.
92
Before you give a try / Re: Possibility of porting Nutyx to AArch64?
« Last post by Thierry on Mon Nov 19 13:41:29 2018 »
A good start is the CLFS Project:

http://clfs.org/

and you look for ARM construction

Best regards,
Thierry
93
Before you give a try / Re: Possibility of porting Nutyx to AArch64?
« Last post by stratact on Sat Nov 17 02:27:16 2018 »
Hi Thierry,

Can you tell me the steps or give me a tutorial of what you have done, I'm curious to try it out myself.
94
Before you give a try / Re: Possibility of porting Nutyx to AArch64?
« Last post by Thierry on Fri Nov 16 22:19:45 2018 »
I would love to. After several attempts, I had to give up. I wasn't able to do it
95
Before you give a try / Possibility of porting Nutyx to AArch64?
« Last post by stratact on Fri Nov 16 08:19:15 2018 »
Hi,

I was wondering if Nutyx has any plans to support the ARM architecture, specifically ARMv8/AArch64? I would like to try installing this distro on my Banana PI W2 board.

If there aren't any plans, is there an easy way to bootstrap Nutyx to this specific architecture?
96
From ISO / Re: mkswap in nutyx-setup changes uuid of all swaps
« Last post by fungalnet on Sun Oct 21 15:05:41 2018 »
I never allow the installer to do any partitioning on its own, I'd rather do this on my own afterwards.
If you have a swap partition already in the system all you have to do is add a swap line to your fstab.

What sounds like happened is that your swap partition was overwritten by a new one with a new uuid and all other installations that had the old id lost it, so you have to replace it with the new one on /etc/fstab on each one affected.

Code: [Select]
UUID=abcde-fghikk-123456-7890123   swap   swap   defaults,noatime   0   0or
Code: [Select]
/dev/sdaxx   swap   swap   defaults,noatime   0   0
works with most linux I've tried.
then do
Code: [Select]
$ sudo mount -a
$ free
$ sudo swapon /dev/sdaxx
$ free

to verify that it is active immediately after the swapon command is issued.
Similarly you can create a swapfile like /etc/swapfile , use dd to copy /dev/zero x times in it to set the size. 
Code: [Select]
# sudo dd bs=1K count=1024K if=/dev/zero of=/etc/swapfile1k x 1024k = 1GB of swapfile.  But I don't recommend this as much because the swap area can be used in case of a crash with journaling abilities to correct the partition after the crash.  If the swapfile gets corrupt as well your partition may be gone.  This is why it is good to have swap even if you have 4 times more ram than you ever use.  This I think goes along the use of restore=/swap/...  in the linux boot line

97
From ISO / Re: mkswap in nutyx-setup changes uuid of all swaps
« Last post by Thierry on Sat Oct 20 14:43:18 2018 »
This is not an issue because I can't see what's the benefit of it
98
From ISO / Re: mkswap in nutyx-setup changes uuid of all swaps
« Last post by Dwanmealy on Thu Sep 27 02:27:34 2018 »
The feeling of me now is very glad to be with everyone here.
99
Before you give a try / Re: Any guarantees of future environment for NuTyX?
« Last post by Dania5583 on Sat Jun 16 16:57:54 2018 »
Hi Bozonius Hi Thierry
I think there is a mismatch between the version of virtualbox you use.
Bozonius says  he uses 5.1.12 (are you sure because your test show that you are uncompressing GA 5.2.12) and you Thierry 5.2.12 on both sides.
Normally you must use the same level on both the host and the guest if you have virtualbox 5.1.12 the GA must would be 5.1.12. To complicate the Nutyx kernel has the modules of  virtualbox 5.2.12 compile in.

if you use 5.1.12 the best way is to upgrade Virtualbox to 5.2.12 on the host

Best regards Daniel
100
From ISO / Install NuTyX in TURBO modus
« Last post by Thierry on Wed Jun 13 19:04:16 2018 »
Install NuTyX in less then 90 seconds is possible:

Pages: 1 ... 8 9 [10]